DNC 連線軟體 CNC機台 連線軟體 下載 真正免費
免費 DNC 傳輸軟體 NC 編輯軟體 真正免費
德國 日本 流行的 ONECNC 加工軟體
OneCNC 科技現代智慧的CAD/CAM(按此回主畫面)
dnc dnc 連線 傳輸 SIEMENS POST FANUC POST 後處理 Heidenhain 530i.PST Okuma OSP 5020.PST 後製處理 Mill LATHE Machine Haas Control 4-axis 5-axis
DNC 軟體下載處 (需登載):
http://www.onecnc.com/support/downloads/nclink-registration
http://onecnc.net/en/support/downloads/nclink-registration
DNC 軟體下載處 :(中文 )
http://onecnc.net/zh_tw/support/downloads/nclink-registration
登載後 約20分鐘, 您mail 收到下載指令
大家放心登載, 表示大方使用, 誰怕誰 ,您說對不對。
現今 軟體 哪一家沒有間諜偵蒐,您最好千萬不要用盜版軟體
你上網又使用盜版軟體, 真活該, 你在何處用, 幾點鐘用, 他人都在看
24 H 的
安裝後請參閱 HELP檔:有關參數設定
3條線之連接法 屬於 軟體交握
Fanuc 0 Series Controls Suggested Cable Pin Out
| CNC Control | Computer 25 Pin | Computer 9 Pin |
| I/O Port | RS232 Port | RS232 |
| DB-25 Male | DB-25 Male | DB-9 Male |
| 1 (Chassis ground) | (Not connected) | (Not connected) |
| 2 | 3 | 2 |
| 3 | 2 | 3 |
| 7 | 7 | 5 |
| 4 and 5 jumpered | ||
| 6 8 20 jumpered |
Notes on Suggested Machine Control Settings
| 1. | Set the PWE parameter to off. The machine will go into Alarm mode as you are setting the parameters. After done setting the parameters set PWE back on and hit Reset. |
| 2. | Above procedure unnecessary to change Handy Page settings |
| 3. | On 0 Series Controls using ISO format, only Baud rate and # of stop bits can be set. Always use Even parity, Word length 7, and 2 Stop bits. |
| 4. | All Parameters set by 8 bit numbers are read right to left, e.g. Bit 0 is the rightmost bit and Bit 7 is the leftmost bit. |
| 5. | Control must have tape reader to do direct DNC. To direct DNC, go to tape mode, set up OneCNC to Send and Wait for XON, hit Cycle Start at the CNC. To pause direct DNC turn Feedrate Override to 0%. |
Suggested Machine Control Control Parameters
| #0002 | - Set Bit 0 to 1 for 2 Stop Bits-I/O = 0 Set Bit 2 to 0 for RS-232 Input |
| #552 | = 10 (4800 Baud) |
Suggested Machine Control Set Page Settings
| I/O | = 0 |
| ISO | Format |
Suggested OneCNC Communication Send Settings
| Baud Rate | 4800 (Suggested starting point) |
| Parity | Even |
| Data Bits | 7 |
| Stop Bits | 2 |
| Handshake | Software - XON - XOFF |
| Start at Machine | Tagged active |
| First Lines | % |
| Last Lines | % |
| Remove Spaces | Tagged active |
Suggested OneCNC Communication Settings for Receive
| Baud Rate | 4800 (Suggested starting point) |
| Parity | Even |
| Data Bits | 7 |
| Stop Bits | 2 |
| Handshake | Software - XON - XOFF |
| Receive Timeout | 10000 |
| Strip at end of Line |
The settings are automatically saved when exiting the settings and they are saved to the currently loaded machine configuration. The Receive and Send settings are separately saved.
來自: http://blog.sina.com.tw/ricky_may/article.php?entryid=633852
留言列表
